A full service car wash concentrates on more than just the outside of your car. Car washes that offer full car wash service will also clean the inside of the vehicle and even check the tire pressures and fluid levels. They are one of the most comprehensive types of car washes and represent excellent value for money.High levels of detailing work can beexpected from a full service car wash.What should you really know about full service car washes? Detailcentral.com.au car wash products is a revolutionary environmental friendly (eco-friendly and green) product resulting from years of research and development.

A full service car wash should always start with a hand washing of the exterior of the car. Anyone who’s been through a mechanical car wash will know that only a hand wash that can get to all the dirt on the car.

The hand wash should also cover the wheel wells and a full service will includeopening the door and washing the door jambs which isan area that’s rarely cleaned properly. There should also be special cleaners used on the tires. Anything less than this doesn’t qualify as a full service car wash.

Most full service car washes will offer different levels of detailing with different prices available. The most expensive can be quite costly but will give a great deal for the money. Unless you’re very messy, a car won’t need a full detailing too often although the car wash operator might try to persuade you otherwise. Go for the level of car wash service that you need, not what they want to sell you.

Most car wash employees are completely honest. However, there will always be a few who aren’t.Remember that you aregiving them full access to your vehicle so it makes sense to keep your valuables either on you or out of sight. Check the car wash to see if it has a disclaimer notice about your possessions. If you’re concerned, keep an eye on your car as it’s cleaned or source a suitable alternative.

It takes 250 liters of water to wash the average car andthis represents a huge amount ofwaste. Aprofessional full service car wash will invest in a system that reclaims and recycles at least some of the water (in some states, this kind of system is mandatory because the waste water contains detergent whichcould find its way into the water system).

If this is an issue that concerns you, ask before you commit to using the car wash and if you’re not satisfied, go elsewhere. Be aware, too, that if recycled water is used for a high pressure wash, it can have an adverse effect on the finish of your car.

The very best full service car washes have a professional attitude and the best equipment.Professional companiesinvest in te best materials andhave the knowledge of which equipment is the best for working on your car.

This extends to the type of detergent used or even the kind of leather used for drying a car. Some products are more effective than others. Asking questions can help you determine how professional the full service car wash really is.

Whether or not to steam clean a car engine hurts it or not depends on the age and condition of the engine, and the way it is done. If you take it to a place that knows what they are doing and does the job correctly, then your car engine will be fine. However, if not, it might possibly damage seals or other parts. It is not recommended for all types of car engines, so you should also check with your car’s manufacturer for more information.

If you decide to go ahead, be sure to dry off everything in the engine when you are done. Steam cleaning is usually to clean off things like oil and sticky buildup.

Yes, it is possible to get a no touchcar wash without water when you don’t want to use water on your vehicle. There are special car cleaning places that you can take the car to in order to have this done, or you can buy special brands of car spray cleaner that you just spray on the car and buff off with a soft cloth. One such product is called Freedom Waterless Car Wash. Another is called Meguiars, but there are other brands as well you can try.

There are both organic and chemical versions of products made for a waterless car wash. It depends on what you are looking for.

Yes, it is possible to do a car wash without water when you want the option. There are special car cleaning places you can take the car to in order to have this done, or you can buy special brands of car spray cleaner that you just spray on the car and buff off with a soft cloth. One such product is called Freedom Waterless Car Wash. Another is called Meguirs, but there are other brands as well you can try.

There are both organic and chemical versions of products made for a waterless car wash. It simply depends on what you want.

If a steam jet car wash is applied correctly and the person handling the stream uses the correct amount of pressure, then the wash won’t hurt the paint job on your car. The advantage of a steam wash is that it has no run off, uses no chemicals, and saves water. All in all, it is a great way to wash your car or truck and help to also save resources and the environment. Most car paint is designed to hold up under a lot of different weather conditions, so this shouldn’t be any different than bad weather.

When it comes to finding the best car wash soap, one thing to remember is to be careful not to use a product that strips the wax off your car. This means don’t use dish washing liquid, as it is harsh and not good for the body of your car. One top product that seems to be popular with car washers is Turtle Wax. A product you can buy in most hardware or car auto parts stores.

It is inexpensive and easy to use. You may also ask your dealership if there are special soaps needed for the type of car you have, or try other brands you can find at the store.

Browse a huge selection of local inventory.

We can help you sell your car for FREE.

Wheel woolies are microfiber brushes for cleaning deep inside wheels and rims with the help of your power drill. Polished concrete is strong, durable and low maintenance while having that earthy texture of stone with a polish equal to granite. Here is how it is done. Before you start buffing, care has to be taken that impregnated stones or foreign materials that could cause potential damage to the tire buffing machine needs to be removed by the operator. Detailing brushes use to remove fragments in your car before the detailing process happens.

It is similar to traditional polished terrazzo which is very flat and poured as a special mix to make the finish more successful. Polished concrete floors can also look almost bumpy and have little or no aggregate showing. Flatness and polishing are not necessarily the same thing which is a good point to clear up before agreeing to your project.

It costs extra time and diamond wear to cut floors with a concrete grinder until they are flat. They can either be ground flat to fully expose the aggregate like terrazzo, or the aggregate can be partially exposed, or the concrete grinding can expose no more than the fine sands at the surface. It often takes skill and experience to control the process of polished concrete floors and the quality of the concreter’s original laying work is also a contributing factor in the quality of the finish. Where the aggregate is a feature special materials can be added to the wet concrete mix such as coloured pebbles, metals and glass to enhance the final appearance.

Most people are unaware that there are ten to fifteen steps for polished concrete floors which takes a long time to complete and can be quite expensive.

Typically it takes many grinding passes to finish a highly polished floor although there are other ways as explained later. The general rule is to double the diamond grit size under the concrete grinder for each pass so a contractor might start with very coarse, 16 or 32 grit size diamonds, then use 60 grit diamonds followed by 120, then start again with a 50 grit diamond resin pad instead of a metal segment. Using the resin pads the steps may be 100, then 200, 400, 800, 1500 and finally 3000 grit. That would be ten separate grinding passes which does not count the two other essential steps.

Two more essential steps:

1. Hardening the surface

Polished concrete floors usually have the surface hardened with a chemical before the second, third or fourth grinding pass. The chemical soaks into the floor to a few millimeters (up to half an inch) and causes a chemical reaction to take place that makes the floor harder and easier to polish to a high finish. These floors are very strong and durable without having a surface coating.

2. Filling holes

After the first concrete grinder pass removes the top layer of concrete paste it will expose millions of tiny air holes. If these are not filled before the hardening process then the final polished concrete floor will show these unsightly imperfections. The holes are usually filled with an acrylic tile adhesive type of product mixed with either the grinding dust or cement powder which is hand scraped across the floor using a trowel. The preferred way to fill the holes is to spray the acrylic adhesive ahead of the grinder so that the diamonds mix it into the holes with the grinding dust on the third or fourth pass at around 120 grit. This method is faster and the dust matches the colour of the floor to hide the holes better than when using cement powder.

Very flat or slightly bumpy polished?

Some floor grinder machines are designed to produce a very flat floor by cutting off the high spots while some others are designed to follow the contours of the floor more. If the surface is to be polished without necessarily exposing the aggregate then only the finer resin pads need to be used on a concrete grinder that allows for movement of the pads so they can follow the contours of the surface. This will result in a polished floor without showing the pattern and texture of the exposed aggregates within the concrete which is faster and less expensive. Hardening can still be an advantage to help the durability of the surface and to produce a final gloss.

Problems with exposed aggregate

Sometimes the finish of exposed aggregate can be uneven if the mix of concrete was poured unevenly or finished off poorly. Boot marks or kneeling board marks can appear suddenly because they have pushed the aggregate down further which might require grinding down another two or three millimeters (quarter of an inch) which will cost more than was quoted. Grinding this far may not be what the customer wanted either so it can be a risk.

Single head or multiple head machines

Original terrazzo grinding was done with single head floor grinders until the production of three-head planetary machines. Planetary means that each head turns one direction while the turntable that houses the heads turns independently in either the same direction or the opposite direction. Some grinders can vary the direction of both the turntable and the heads and some can vary the speed of each. There are also multiple head planetary machines with four or more heads.

The planetary heads can follow the contours better than single or twin head grinders and are faster to use with less effort due to eliminating the requirement to physically move the grinder from side to side or in a circular motion. Single head terrazzo grinders should be moved in a circular motion to avoid grinding lips or shoulders.

Edging

As with wood floors the edges must be finished separately to the main floor area because the large machines may bump and damage the walls if they are used too close. For the first grinding passes a nine inch angle grinder is used having a diamond wheel attached with a dust extraction shroud fitted to remove the dust. The sit-down-to-use edge grinders are more controllable than stand up grinders while kneel-to-use grinders have good control, but are exhausting.

After the first two or three cuts a different dust extraction shroud with a corner feature is used with a seven inch polisher or a five inch, multi speed grinder to polish with resin pads and get tight into the corners.

Simple polished concrete floors “look”

The number of processes for polishing concrete can be reduced by up to 60% and still achieve a similar appearance by grinding and then coating with a clear sealer. The first step is to grind with 30/40 grit diamonds to expose the aggregate, then fill all the small air holes as described above (in 10 to 15 steps….) before a second grind with 60/80 grit or 80/100 grit diamonds.

This will produce a smooth enough surface to coat with a sealer. Polyurethanes are very hard sealers with a high gloss and can be purchased as UV stable to stop yellowing (usually double the price of non UV stable urethanes), clear epoxy sealers are not as smooth and will chalk and deteriorate if exposed to sunlight and acrylic sealers have a much shorter lifespan due to their poor resistance to wear. Two coats are necessary to provide a high gloss level.

Different ways to achieve “polished concrete”

The first is to cut the floor with coarse diamonds until all the high spots have been removed to produce a flat floor and then use all of the 12 to 15 steps to eventually polish it or as it is sometimes called, hone it. This is the true polishing system.

A variation of the above is to cut perhaps half of the height of the higher peaks by starting with a medium coarse diamond grit and proceed through to polishing using a machine that can ride up and over small rises.

A third alternative way of producing a honed surface is to start with relatively fine diamonds and simply polish to top of the surface after hardening without removing much of the top cement paste. It is easier to do this when the floor has been laid flat and smooth.

Lastly, a “polished look” can be obtained by grinding with coarse diamonds and then fine diamonds before coating over with a clear sealer.

Only truly polished floors will retain their gloss with little maintenance because all coatings scratch with wear and lose their high shine. Special buffing pads on a standard floor polisher that contain very fine diamonds can be used to maintain cleanliness and the high gloss levels of true polished concrete. Janitors can be provided with these and keep the floors in great condition without special treatment.

Some hire companies provide the grinding equipment for do-it-yourself concrete polishing and have all the pads for the purpose. This may not be so economical though because the pads may be only half worn when you finish depending on the area involved.

Ron Black has worked in the polished concrete industry with experience in both grinding and machines. He is part of Situp Products’ team and has written many pages of information for the concrete grinding website [http://www.situp.com.au] Find out the new process in polishing your car.

Article Source: http://EzineArticles.com/expert/Ron_Black/336833

Article Source: http://EzineArticles.com/2394248